1.800.363.1962

TECHNICAL SUPPORT

Online Technical Data

Complete documentation specific to your tool can be retrieved by scanning the QR-Code applied on the tool.
You will find the Operation Manual, Part list and Schematic referring to your tool as it was manufactured.
You will also find useful information for ordering replacement parts.
Always refer to your tool schematic before ordering parts.

Documentation can also be retrieved by entering the complete URL listed around it in any web browser (eg. ts.primatech.ca/250A-143);
or by following steps below.

The tool code can also be listed on some tools above the Serial Number of the tool.

Enter the tool code here:

(for unlisted tool code, proceed below)


P250AL

250A Primpact -Series 16ga nailers & staplers with adjustable base

Select the tool code found on the QR-Code applied next to the name plate:

  • 250A-v143 - Introduction of the new Primpact module
  • 250A-v142 - Introduction of the LoadXtend magazine for staplers
  • 250A-v141 - Introduction of the new Roller Base
  • 250A-v140 - Earlier models

If no tool code found on tool, enters



Invalid Serial Number

Check here if no QR-Code or S/N found on tool.

Parts list for all versions.


P250FL

250F Primpact -Series 16ga nailers & staplers with fixed base

Select the tool code found on the QR-Code applied next to the name plate:

  • 250F-v143 - Introduction of the new Primpact module
  • 250F-v142 - Introduction of the LoadXtend magazine for staplers
  • 250F-v140 - Earlier models

If no tool code found on tool, enters



Invalid Serial Number

Check here if no QR-Code or S/N found on tool.

Parts list for all versions.


Q550L

550A Primpact -Series 18ga nailers with adjustable base

Select the tool code found on the QR-Code applied next to the name plate:

  • 550-v143 - Introduction of the new Primpact module
  • 550-v141 - Introduction of the new Roller Base
  • 550-v140 - Earlier models

If no tool code found on tool, enters



Invalid Serial Number

Parts list for all versions.


Q900

900A Primpact -Series 18ga EDGE nailer with adjustable base

Select the tool code found on the QR-Code applied next to the name plate:

  • 900-v143 - Introduction of the EDGE nailer

If no tool code found on tool, enters



Invalid Serial Number

Parts list for all versions.


P145

145 PRO-Series 16ga nailer/stapler with fixed base

Select the tool code found on the QR-Code applied next to the name plate:

  • 145-v180 - Introduction of the P145 nailer/stapler

If no tool code found on tool, enters



Invalid Serial Number

Parts list for all versions.


P245L

245 PRO-Series nailers & staplers with fixed base

Select the tool code found on the QR-Code applied next to the name plate:

  • 245-v142 - Introduction of new magazine for staplers
  • 245-v140 - Earlier models

If no tool code found on tool, enters



Invalid Serial Number

Parts list for all versions.


P240

DIY-Series Pneumatic tools

  • P210 Pneumatic Nailer
  • P220 Pneumatic Stapler
  • P240 Pneumatic Nailer
  • P260 Pneumatic Stapler

H330L

Manual tools

  • H300 Single-Hit Manual Nailer
  • H330 Multi-Hits Manual Nailer
  • Q500 18ga Manual Nailers

Q180
Q180 18ga stapler

P534FN
534FN 15ga DA finish nailer

Specialty Pneumatic tools

  • Q180 18ga Stapler
  • 534FN Nailer for 15ga 34° DA nails

Miscellaneous

Other documentation

Usefull applications

General recommendations

ico-caution Pneumatic nailer are designed to be operated with a 2.8 lbs mallet. Use ONLY the rubber end of the mallet to actuate the tool. The use of the steel end will damage the head assembly and will VOID the warranty.
oil Pneumatic tools require minimal lubrication. Few drops of oil weekly in the air inlet is sufficient to reduce wear and prolong life.
ico-compresr Troubleshoot your compressed air delivery system. Many of problems come from a faulty or inadequate compressed air supply system. Read this section before attempting to repair the tool.